收藏本站
preset phototransistor output level is reached.
At this time, the LED drive current is locked and maintained until
the calibration pin is grounded. If for some reason the LED drive cur-
rent reaches the maximum allowable value, a RED warning light will
turn on. During the calibration process, remote monitoring of J1-Pin
5 allows the designer to ensure the system is calibrated (this output
should be at the preset calibrated output level of 1/2 Vcc when the
calibration procedure is completed). Adjusting the phototransistor
load resistor may allow the system to calibrate properly.
After the calibration process is complete, the device is ready for
acknowledgement of a change in the signal. The design engineer
6
can monitor either the Analog Output (J1-Pin 5) or Logical Output
(J1-Pin 2 or J1-Pin 3).
Connection of the analog ouput to additional circuitry allows the
design engineer to set any reference point to recognize an optical
change for the device being monitored. The Analog Output can be
used with reflective devices to monitor small changes in the distance
from the device.
The Logical Output will change state once the preset optical light
condition is reached. Logic Out A” (mating connector orange wire)
switches when the optical output signal decreases below approxi-
mately 1/3 of Vcc while “Logic Out B” (mating connector blue wire)
switches when the optical output signal increases above approxi-
mately 2/3 of Vcc.
As with all optical devices with logic outputs, the switching condition
is consistent with the phototransistor receiving a preset light level.
OCB100-KIT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
OCB350L062Z BOARD CALIBR CIRCUIT OPB350L062
OJ-SS-112LM,000 RELAY GEN PURPOSE SPST 3A 12V
OJ-SS-124DM,000 RELAY GEN PURPOSE SPST 5A 24V
OJ-SS-124HM,000 RELAY GEN PURPOSE SPST 10A 24V
OJE-SH-112HM,000 RELAY GEN PURPOSE SPST 10A 12V
OJE-SS-124DM,000 RELAY GEN PURPOSE SPST 5A 24V
OJE-SS-124LMH,000 RELAY GEN PURPOSE SPST 8A 24V
OMA160S RELAY OPTOMOS 50MA SP-NO 6-SMD
相关代理商/技术参数
OCB100-KIT 制造商:TT Electronics / OPTEK Technology 功能描述:Auto-Calibration Design Kit
OCB-1250 制造商:Heyco Products Inc 功能描述:
OCB-1375 制造商:Heyco Products Inc 功能描述:
OCB-1500 制造商:Heyco Products Inc 功能描述:
OCB350L062Z 功能描述:光学开关（透射型，光电晶体管输出） Calibration Circuit With OPB350L062 RoHS:否 制造商:Omron Electronics 输出设备:Phototransistor 槽宽:3.4 mm 光圈宽度:0.5 mm 集电极—发射极最大电压 VCEO:30 V 最大集电极电流:20 mA 正向电流: 安装风格:Through Hole 最大工作温度:+ 85 C 最小工作温度:- 25 C 封装:
OCB350L125Z 功能描述:光学开关（透射型，光电晶体管输出） Calibration Circuit With OPB350L125 RoHS:否 制造商:Omron Electronics 输出设备:Phototransistor 槽宽:3.4 mm 光圈宽度:0.5 mm 集电极—发射极最大电压 VCEO:30 V 最大集电极电流:20 mA 正向电流: 安装风格:Through Hole 最大工作温度:+ 85 C 最小工作温度:- 25 C 封装:
OCB350L187Z 功能描述:光学开关（透射型，光电晶体管输出） Calibration Circuit With OPB350L187 RoHS:否 制造商:Omron Electronics 输出设备:Phototransistor 槽宽:3.4 mm 光圈宽度:0.5 mm 集电极—发射极最大电压 VCEO:30 V 最大集电极电流:20 mA 正向电流: 安装风格:Through Hole 最大工作温度:+ 85 C 最小工作温度:- 25 C 封装:
OCB350L250Z 功能描述:光学开关（透射型，光电晶体管输出） Calibration Circuit With OPB350L250 RoHS:否 制造商:Omron Electronics 输出设备:Phototransistor 槽宽:3.4 mm 光圈宽度:0.5 mm 集电极—发射极最大电压 VCEO:30 V 最大集电极电流:20 mA 正向电流: 安装风格:Through Hole 最大工作温度:+ 85 C 最小工作温度:- 25 C 封装: